GCr15轴承钢成品套圈热处理后点线状缺陷原因分析

在热处理后的GCr15成品轴承套圈表面发现疑似裂纹的点线状缺陷。通过无损检测、光学显微镜、扫描电镜、能谱分析等手段对缺陷进行分析,发现缺陷处存在较大尺寸的氧化铝和硅酸盐复合夹杂物。通过采取“高拉碳”、“白渣操作”、“软吹”“保护浇铸”等措施后,钢水纯净度得到进一步提高,避免了点线状缺陷的再次发生。     

Effect of microbial hydrogen consumption on the hydrogen permeation behaviour of AISI 4135 steel under cathodic protection

The feasibility of microbial hydrogen consumption to mitigate the hydrogen embrittlement (HE) under different cathodic potentials was evaluated using the Devanathan-Stachurski electrochemical test and the hydrogen permeation efficiency η. The hydrogen permeation efficiency η in the presence of strain GA-1 was lower than that in sterile medium. The cathodic potential inhibited the adherence of strain GA-1 to AISI 4135 steel surface, thereby reducing the hydrogen consumption of strain GA-1. The adherent GA-1 cells were capable of consuming ‘cathodic hydrogen’ and reducing the proportions of absorbed hydrogen, indicating that it is theoretically possible to control HE by hydrogen-consuming microbes.     

浅析火力发电厂汽水系统中内径管与外径管的设计选择

按照管道加工工艺的不同,管道可分为内径控制管和外径控制管。通过热轧工艺生产的外径控制无缝钢管,可满足火力发电厂汽水系统中绝大部分管道的使用要求。对于超(超)临界机组的主蒸汽和高温再热蒸汽管道采用的P91/P92材质的大口径厚壁无缝钢管,由于对材料性能和加工工艺有特殊要求,因此宜采用内径控制管。     

淬火温度对G105钢组织和性能的影响

利用硬度计、拉伸试验机、冲击试验机和光学显微镜等手段,研究了G105钢分别在890、910和930 ℃保温150 min淬火,随后进行630 ℃保温180 min回火处理后组织和性能变化。结果表明:随着淬火温度的升高,G105钢淬火硬度越来越高;经回火处理后,淬火温度为890 ℃和910 ℃时,调质硬度无太大差异,分别为33.2 HRC和32.7 HRC,淬火温度为930 ℃的调质硬度相对提高约1.5 HRC。试验钢强度随着淬火温度的升高也呈现升高趋势,但冲击韧性呈先升高后下降的趋势,这主要是由于调质后存在粒状碳化物的析出现象,导致其冲击韧性显著下降,故认为当淬火温度选取910 ℃时,获得的G105钢综合力学性能较佳。     

55SiCr弹簧钢中的残留奥氏体与碳化物

通过扫描电镜(SEM)、电子背散射衍射(EBSD)、透射电镜(TEM)、X射线衍射仪(XRD)、热膨胀仪、洛氏硬度计等手段研究了弹簧钢55SiCr的组织和相变点以及残留奥氏体和碳化物在热处理过程中的组织演变。结果表明:55SiCr弹簧钢淬火后残留奥氏体以块状分布在基体上;随回火温度的升高,残留奥氏体减少并呈粒状和薄膜状分布;C在残留奥氏体中富集,使其稳定性增强;Si抑制了碳化物的析出,提高了残留奥氏体的稳定性。低温回火时,Si延缓了渗碳体析出;高温回火时,C原子扩散速率提高,促进渗碳体析出,引起体积的收缩。慢速加热回火时,C有足够的时间扩散,从而促进渗碳体的形成,使渗碳体的形成温度提前;快速加热回火时,C来不及扩散,抑制了渗碳体的析出。回火加热速率一样时,试验钢的硬度随回火温度的提高而下降。当回火温度为400 ℃时,硬度值最大为51 HRC;当回火温度为650 ℃时,硬度值最小为37 HRC。当加热速率为0.1 ℃/s时,硬度值最小为33 HRC;当加热速率为200 ℃/s时,硬度值最大为40 HRC。     

Optical spectroscopic and electrochemical characterization of oxide films on a ferritic stainless steel

Colored oxide films that form on ferritic stainless steel in a high-temperature, oxidizing environment and correspond to different chemical compositions can cause a deterioration of pitting resistance and corrosion performance. Herein, optical spectroscopic and electrochemical techniques have been used to reveal the relationship between color, chemical composition, and corrosion resistance of oxide films formed in the temperature range from 400°C to 800°C for 30 min and at 800°C for 10, 20, 30, and 60 min. The substrate with a thin and dense passivation film leads to a low pitting potential but high corrosion resistance. Oxide films of yellowish or brownish color formed below 600°C are mainly iron oxides, which correspond to low corrosion resistance. No passivation characteristics can be observed for polarization curves of oxide films formed at 500°C and 600°C. The color of oxide films varies from blue to dark gray with the increase of oxidation time at 800°C. Corrosion resistance changes with different proportions of Fe₃O₄, Cr₂O₃, and FeCr₂O₄. The gray oxide films formed at 800°C for 30 min exhibit the lowest pitting susceptibility and the highest corrosion resistance.     

萃取塔数学模型及过程强化的若干研究进展

萃取塔因生产能力大、占地面积小、密闭性好等优点，在石油、化工、生物、医药和环境工程等多领域被广泛应用。本文从以下几个方面介绍了萃取塔近些年的研究进展：综述了传统萃取塔（脉冲萃取塔、转盘塔与Kühni塔等）的水力学、轴向扩散与传质模型的发展，分析比较了表面张力、传质方向、放大效应等因素对模型的影响；介绍了计算流体动力学（CFD）在萃取塔中单液滴、单相流模拟、液-液两相流模拟、外加能量模拟、与群体平衡模型（PBM）耦合模拟中的应用进展；介绍了国内外设计开发的新型萃取塔，包括改变传统塔的内构件和引入多种外场能量等方式来强化相间传质。研究表明，将先进实验研究方法、准确经验模型和可靠理论计算相结合，将会是萃取塔研究的重要手段和方向。     

热处理工艺对30MnCrNiMo高强钢组织与性能的影响

借助全自动淬火膨胀仪测定钢的Ac₁、Ac₃相变点,通过对试验钢进行淬火+亚温淬火+回火热处理和淬火+回火热处理,研究了两种热处理工艺下30MnCrNiMo高强钢的组织与性能。结果表明:30MnCrNiMo高强钢的Ac₁、Ac₃相变点分别为653、807 ℃。采用淬火+亚温淬火+回火的热处理工艺所获得的马氏体和铁素体复相组织比直接淬火+回火得到的全马氏体组织更为细小、均匀,试验钢的屈服强度为1499 MPa,伸长率为14.0%,室温、-40 ℃冲击吸收能量分别为35.5和29.5 J,钢的塑性和冲击性能显著提升,有效改善了30MnCrNiMo高强钢的强韧性能。     

Effects of Rare Earths on Toughness of 31Mn2SiRE Wear-Resistance Cast Steel

The toughness of 31Mn2SiRE wear-resistance cast steel were increased by means of RE compound modification and high temperature austenitizing. The results show that the microstructures can be refined, needle and network ferrite are eliminated, the dislocation density and the quantity of dislocated martensite are increased remarkably, and the shape and distribution of inclusions are improved by the addition of RE. Therefore, the mechanical properties of the modified steel can be greatly increased, especially the toughness (αK) by 44%, yield strength (σs) by 10%, and elongation (δ5) by 42%.     

不锈钢塔器在硫酸装置中的应用

摘 要:主要介绍Sasol Agri公司硫酸四系统的技术改造,分两步进行,第一步更换转化器、热换热器及主省煤器,生产能力由1600t/d提高到1750 t/d,且鼓风机出口压力很低。第二步更换干燥塔、二吸塔及冷换热器,连续生产能力在1950 t/d以上。使用不锈钢材质及克瓦纳·凯密迪公司专有的换热器,使装置的改造相当成功,维护及操作费用较低,并具有较大的灵活性和可操作性。